Gerald’s Chest of Drawers and Doll Desk – Viewer Project
Filed under: Chest of Drawers, Childrens' Projects, Desks
This Viewer Project post is a two-fer. Gerald sent us pics of a beautiful chest of drawers as well as a doll desk for his daughter. Check it out:
The Chest of Drawers
My wife’s sister asked that I build her son a chest of drawers similar to one that she had seen in a furniture store near her house. It was a painted item of poor quality. This would be my first opportunity to design and create a piece from start to finish.
I started with the overall dimensions and began creating the shop drawings for the piece. I am a Professional Land Surveyor by trade so I was able to utilize Autocad for the drawings. I went through every piece in my home to get different ideas on how to design the case for the piece. The design I ended up using seems pretty simple once I broke it down into the components. The sides are a frame and panel between the two legs. The supports for the drawers are a simple frame design and really worked well. The top is an edge glued panel of the best stock I had on hand.
The drawers are constructed using a type of locking rabbet joint in front and dado in the rear. As can be seen on the photos I reinforced all interior corners with small mitered pieces just to add more strength to the joints. This piece is going to a small child and I wanted to be sure he could not pull the drawers apart. The drawer slides are full extension glides. A little unusual for a furniture piece but again I wanted to make sure that if he was to lean down on the drawers or to climb on them that they would support the load and not give way.
The drawer fronts for the top three drawers and the middle two were cut from one piece of stock to insure grain continuity across the piece. Really makes the piece stand out when completed. All joinery on this project are Domino’s from Festool. Thanks again to Dennis Kent of Woodcraft for suggesting this tool for my shop. It is an awesome tool that makes quick, strong and accurate joinery.
The finish was lots of fun to watch come together. The cherry really comes to life during the finishing process. I started by sealing the raw cherry with a wash coat of shellac to help control blotching. This was followed by two coats of Minwax “Cherrywood” gel stain. The gel stain was easy to work with and ended up being very transparent. It really allowed the grain to show through on the completed project. The second coat was when the character of the cherry began to show. The top coat is lacquer sprayed on with my Earlex HVLP system. Multiple coats were applied to allow wet sanding and hand polishing up to the desired sheen. I think the top came out nicely once the sanding and polishing were completed. Antique brass hardware completed the look and matched nicely with the cherry.
The Doll Desk
My daughter Sarah has several American Girl dolls and loves to play school with them. She asked daddy for a desk for “Julie” and I set out to see what I could come up with.
This project was built pretty much on the fly. Sarah had seen an old type desk at our church and wanted Julie’s to be like it. I decided that since I had some nice Red Oak left from from another project I would use it. The desk compartment is a simple box with a slant top that opens to storage below. A pencil groove was routed in the flat area near the top. Corners are simple rabbets and the bottom is tempered hard board floating in a groove milled into the sides.
The chair is sized to fit Julie and utilized some thin stock that was left over from another project where I had resawn some oak for another use. The sides utilize a half lap joint and are surprisingly strong. The seat and back stretchers are the thin resawn stack that I mentioned earlier. The chair support and desk support is again built from some scrap pieces I had around the shop from larger pieces. 
The original thought was to have the vertical support for the desk and chair be the only pieces under each. Once the pieces were assembled it became obvious that more support was needed laterally to prevent each from racking. I added the mitered braces to help with the flex of the thin stock. I finished the piece with two coats of satin polyurethane.
Now Sarah and Julie can play school in style!
Honduras Mahogany Dresser – Viewer Project
This project is submitted by Tom. Let’s see what he has to say about it:
“Dresser is primarily Honduras Mahogany with Beech internals, Philippine Mahogany drawers and Walnut pulls. A mongrel design (I mean hybrid?)
Sources of design: Began with a Will Neptune article, Anatomy of a Chest of Drawers (2003 May/June Fine Woodworking). From the Summer 2008 Woodwork Magazine I loved Christopher Schwarz’ article, A Better Blanket Chest Design. That supplied inspiration for the plinth. I used dovetails rather than finger joints. Mark Edmundson wrote about NK-style drawer construction in A Better Way to Build Drawers (The New Best of Fine Woodworking). I decided to give it a try. I haven’t seen them mentioned in any other articles, on-line or in print. After making these I still haven’t decided if I like them functionally or from a construction standpoint better than others I’ve used. Any thoughts on this from Wood Whisperer fans?
The November/December 2008 issue of Fine Woodworking arrived just as it was time to figure out the door pull treatment. One of the Four Custom Pulls that Please the Eye by Michael Fortune struck me as perfect. Lastly, the top molding. Trying to decide on basic size/proportions, I held a scrap of drawer runner against the case, below the top. Eureka. I modified the “drawer runner” with chamfer and round over and was very pleased.
Two disasters: Just as the plinth was completed it fell and bounced on the rough concrete of my driveway. Ouch! The structure survived nicely. Thank you, Christopher. But a corner had nasty gouges and tears as well as a few other bashings. At that point I knew this would be a “country” piece. Later, as I foolishly stacked drawers on a rolling cart, one of them fell on that same nasty concrete. Direct hit to a drawer front corner. More sanding and acceptance of “the process being more important than the product.”
Problems?: Of course! When selecting the Mahogany, I liked the look of the 8/4 offerings much better than the 4/4. So this seemed like a good time to try resawing. I used a 3/4-inch Wood Slicer. As soon as the blade exited the wood, that lovely wood sprung to open up huge cups (and/or bows) in each half. Of course I proceeded to cut all of my stock with similar results. By the time I milled the material true it was 5/8-ish rather than the 3/4 I had planned on. On the positive side this saves weight if I ever have to ship it by air. Just doing my part to lessen the carbon footprint.”
Construction Details: The plinth is a dovetailed box with two horizontal supports that are glued into rabbets. Case is screwed into those pieces (no glue). The half-blind dovetailed case has a full top and bottom allowing the show top and plinth to be created without considering case integrity. Case has dadoes for horizontal and vertical dividers with exposed dovetails the three front most inches. Horizontal dividers are mortise and tenon frames, Mahogany for front stile and Beech for other pieces. Vertical dividers, same depth as horizontal stiles on top row are separate pieces, glued in place. Beech dividers float in dadoes since the grain runs opposite of other case members. Bottom molding is simple bevel with small lips at top and bottom. Top molding, mentioned earlier, is a bit more detailed but still rather clean. Finished with five coats of 1:1:1, semi-gloss poly:linseed oil: mineral spirits and then waxed.
You can view more of Tom’s work on his website.
Dustin’s Dresser – Viewer Project
This Viewer Project comes from Dustin. Its a beautiful maple dresser made from……baseboards?!?!? He writes:
I wanted to send you a quick note and some pics of my latest project. I built a dresser for my son’s Christmas present this year and hopefully one that will last him for many years. Looking back at the things I have built in this past year, I can immediately notice that the quality of my work has tremendously improved. I actually built this dresser out of maple baseboard trim. I have a friend who ran across about a truckload of baseboards that someone wanted to sell real cheap and one side of them was primed white, but I could see what was underneath…beautiful hard maple. Why a company would make baseboards like this, I will never understand.
Bedroom Suite – Project of the Week
This week’s project comes from Chad. Let’s see what he has to say:
“Back in 1999, my wife wanted a “nice bedroom suite.” I happily looked into it for her, and was shocked at the cost of a full bedroom suite. Anywhere from $3,000 to $4,500. And surely none of them were actually solid wood. I had just started my hobby of woodworking, and so I asked my wife if she was willing “to have a piece made one at a time.” She said she would be. I designed the first piece, the armoire, and then asked her what type of wood she wanted….she said knotty pine. “Sweet,” I thought, “that is the cheapest wood in the world.” First I made the armoire, then we moved. I then made the dresser and a few months later, I made the end tables. All of this within about 2 years. (hey, I was in the Army, and I was busy defending my country.)”
“Anyhow, I never made the bed because I had bought a nice and inexpensive wrought iron bed, picked up at a garage sale. Earlier this year though, I decided it was about time to “finish” the bedroom suite. I designed the bed to be very simple, but with the same raised panel styling I had used in the other pieces. It took me many nights and weekends, but in the end, I think it turned out pretty good. All of the lumber was purchased at Lowe’s or Home Depot. Each piece had three staining layers of Minwax Golden Oak. With three layers of polyurethane, semi-gloss.”
“Needless to say, my wife is very pleased, and I am happy to have the whole suite completed. As a side note, my wife told me a few years ago that the only reason she agreed to let me build the suite way back when was because, as she says, “I didn’t really think you could do it, so I said yes so that I didn’t hurt your feelings.” I guess it’s easy to please someone with low expectations!”
Check it Out!
Premium Membership
Keep Up With TWW!
Shop our Affiliates
Latest Video
Proud to be Sponsored By:
Support our Advertisers
