Modern Coffee Table – Project of the Week



This week’s project comes from Tom in Canada. Its a beautiful coffee table made from walnut and maple. The exposed joinery is a unique detail and really shows off Tom’s craftsmanship. Let’s hear from Tom himself:

“My name is Tom and i am from London Ontario area (Thats Canada) and I’ve been woodworking and apprenticing for about 6 years making furniture and built-in cabinetry. This is a coffee table i built recently. I wanted to try something with a floating top, and contrasting woods. I think the floating top lets you show off some joinery underneath it, i used sliding dovetails for the legs and some dovetails on the stretcher supports. The top is made of some birdseye hardmaple and the base and legs are walnut. I finished it using a blend of linseed oil, turpentine and varnish. It was my first time trying that mix, and found that it took a long time to get any film build at all (about 5 or 6 coats on top). I’ll maybe try a different ratio to get more solids into the finish next time. Hope you like it.”

Coffee Table Coffee Table Coffee Table


12 Responses to “Modern Coffee Table – Project of the Week”

  1. baldy says:

    That is awesome work!! Love the contrast especially in the dovetail joints!! Bravo my fellow Canuck!!! I aspire to be that precise!! Thanks for the inspiration.

  2. Al Navas says:

    Beautiful, and outstanding craftsmanship, Tom! I look forward to seeing more of your projects; I am glad you shared your work with Marc, or I likely would have missed it.

    —— Al

  3. Mike says:

    Very nice coffee table, Tom. I really like that you can see the dovetail details and the use of contrasting woods. My question is, how did you “float” the top?
    Or, from where is it mounted and with what? I would really like to see the under side of this piece. Great job!
    Mike

  4. Mitch Cutler says:

    Nice table!

    I like the contrast and the detail of the dovetails. Did you cut those in one pass or run a straight bit through first and then use the dovetail bit?

    I like the angles too. Must have been some fancy jigs to get everything right.

    Keep up the good work!

  5. Mattias in Durham, NC says:

    Very nice!

    The 1st and 3rd photos are almost the same – can we have another one of joinery instead?

  6. muddler mike says:

    really nice Tom. Understated, with hidden treasures! Great combo of woods, joinery, and design. It’s one of those pieces that kind of makes you keep looking at it.

    Mike

  7. jim_ny says:

    very nice I to love the looks of the sliding dove tails, on the stretchers did you have the dovetails slide all the way down or did you stop short of the bottom again very nice work

  8. Kip says:

    Most enjoyable!

    Keep up the outstanding work.Its obvious you have well developed design skills in your use of wood color and unique joinery. Please keep sharing,

    Kip

  9. Tomcat1066 says:

    Wow! Very nice piece. I especially love how the top seems to float about the base. It makes for a very interesting effect.

  10. Mike in St. Paul says:

    Tom -

    In a word: COOL!

    Very well done, sir. I wish I had one like that for my living room. Truly awesome job.

  11. Tom says:

    Thanks for all the compliments folks….glad we have a site like this to chit-chat about woodworking! To answer a few questions, the “floating top” is actually just sitting on the 2 maple stretchers going across the middle of the of the apron. Atop the stretchers are 7/8″ spacers (also of maple), that are set back enough that you cant see them unless you look for them (about 3-1/2″) . I just predrilled and shot some screws through the stretcher and spacers, into the top (this may lead to some shrinking/expanding problems i know). And Mitch, i cut the sliding dovetails in one pass on a router table, its not much of an issue, the only thing is you should have a sturdy stop block set up because the bit does like to climb into the wood, a straight bit relief would be good for a less powerful router though, and probobly better on the bit itself too. The stretcher dovetails are just handcut 1/2 blind dovetails. Pretty straightforward; cut a tail, mark it on the apron, and cut the slot. Easy to do when you only have 1 tail and 1 slot to cut (easier than hand cutting drawer sides of multiple pins and tails). Thanks again for all the comments and im looking forward to seeing everyone elses projects…TOM

  12. Edwin from Toronto says:

    Very nice project Tom!

Leave a Reply




Stay Connected

Search

Coming Up

Get Woodworking Week

2012,02,05,0,0,0

Box Week

2012,02,13,0,0,0

Video: Tapping Threads

2012,02,22,0,0,0



The Guild

What is the Guild?

The Wood Whisperer Guild is a unique and interactive online woodworking school. We invite you to join   our premium membership and build 2 projects over the course of a year with Marc and your fellow guild members.

Visit the guild page
for full details.

What's New

Coming Up

Video - The Dovetail

2012,02,10,0,0,0


Woodtalk Online



    Support our Advertisers


    Local Market





    The Guild

    An interactive online woodworking school. Learn how to build furniture at your pace with the aid of incredibly detailed videos. Members recieve numerous other benefits including discounts and access to special live events.

    WoodTalk Online

    Connect with your fellow woodworkers in a friendly environment. Learn something new or simply share your knowledge. Design, Share, Build.

    Stores

    Support us by shopping in our store. DVD’s, t-shirts, hats, coffee mugs, project plans, and more!

    Behind the Scenes

    Education and Entertainment for the modern woodworker.

    Contact

    Education and Entertainment for the modern woodworker.


     
    (n) Copyright © 2010 The Wood Whisperer. All rights reserved.
    Designed and Developed by Underscorefunk Design